Avosdims fly screens

Decided to buy the 'Luxe' screens as they can be provided cut to size. I reckon it takes an hour to cut down a blind, so the 10€ charge is reasonable. Sadly, it adds 2 weeks to an already too long 1 week time to send them. Seriously? It takes you a week to take a stock item off the shelf and put it in a box?? I could understand this at peak mosi season, but in spring??

Box arrived open with the blinds sloshing around. Very sturdy carboard, just not enough bands. Or packing material.

Swarf everywhere, and paint scratched and worn.

Insturction incorrect. Torx T27. WTF who was T27. Turns out they meant posi. 4.5mm HEX. Now that is bizzare. I've over 10 sets of allen keys, plus socket sets. None had that size. Imperial not close either. Jammed a screwdiver in. Must be a common size in China.

Instructions did not cover how to assemble a pre-cut blind. It assumed you were cutting it down.

Avosdims have clearly never fitted their blinds on a real window. Window sill slope. They have to slope else rain will invariably run towards the house. On this 'Luxe' design there is a shitty plastic clip to hold the blind down. This shitty clip is on the outer edge and relies on pressing hard onto the sill. This wont happen on a real window sill. Ended up putting a bold through.

1 window has a nearly flat plastic sill. The shitty clip is nicely compressed. However, the crap design means it's really really difficult to unclip. Arthritis anyone. Don't even try to open them.

The cheap blinds put a much better clip on the inside edge and are much easier to use.

Will I buy again. Probably. I'll order the drop length +5mm and re-cut it to suit the sill, or maybe the cheap one. Avodims are the cheapest by a long way, so take your pick.

Reolink doorbell

I've had a doorbell on the gates for years. So long that the hedge that wasn't there now grows over it. The same goes for the gates orange warning beacon.

Long story short. Bought a Reolink D340W. Ethernet or wifi. Wifi will never work - just too far.

Moved the doorbell to the other pillar, and the beacon to the other side of the existing pillar. Took a bit of effort to get the cat5 across as a lizard had died in the conduit which took a bit of luck to get out.

The 868MHz link just works to the house for the separate chime, but HASS integrates the doorbell, so I can trap the button press if needed.

Changes needed

1. Remove 5V psu for old camera and connect to gates +14V IR beam supply via 250mA fuse.

2. Add 24V supply in place of the 18V supply that fed the gates supply

3. mains delay PCB now fed from IR beam 14V via 270R resistor (used to be 5v)

4. beam broken & gates open sensors now send 14V to house instead of 5V

Circuit is with gate manual

Bosch Ixo

Pretty old, bought around 2009. Battery is a Sony 1.3Ah/20A. As of today it's at 0/6Ah.  Replaced with a 3Ah, 20A Pile Rechargeable 18650 INR18650-25P DMEGC Li-ion 3,7V 2500mAh 20A from Bestpiles.

All fall down

Capvern les Bains, 65130. The end wall of the old Salon de thé fell away. It had a tarp covering the roof for quite some time.

Rat on a wall

 I've seen a rat around the outside of the house, and on the shed roof, but it then disappeared. Turns out they have strong enough claws to walk on walls.

siplec enrouleur automatique

 Bought this a good few years ago when Leclerc had it on offer.

Good enough, but recently it's not been winding back the last metre.

Rip out all the screws on this side. You can leave the black cover in place.

Carefully remove the screw under the rear sticker about half way. Balance it on securely on some wood chocks. Working from the front, it should just come off. If not keep undoing the rear screw a turn at a time. 

With it now open, keep pressure on the black cable reel. Turn the case, ACW holding the reel a until the cable block gets to the case, then add a couple of turns. Reassemble.

It wont matter if the black reel does come away - the spring will just pop out quite safely. But now you'll need to rewind it all. It can be tricky holding the tensioned reel in place and refitting the top. In that case remove the black cover and small centre screw. Then feed the cables through, place the slip ring north/south and refit the cover, passing the cables back through and matching up the square peg of the slip rings.

Sold the bikes

 After over 20 years of riding, we sold the bikes. It's not that we'll stop riding, it's just that we've barely ridden them in 2 years. Too hot, too cold, too many other things to do that we are enjoying more.

Received the money 27/4/26

Last seen at the dealer 😘